:1992 : IEC801-2 :1991 4KV CD, 8KV AD : IEC801-3 :1984 3V/m, 27MHz-500MHz : IEC801-4 :1988 0.5KV Signal Line 1KV AC mains Signature: Full Name : Mikio Moriya Position : iDP-562 User’s Manual General Manager R & D Department CITIZEN...
E. If the product has been dropped or the cabinet has been damaged. F. If the product exhibits a distinct change in performance, indicating a need for service. *iDP-562-RSL/RS, iDP-562-CNL/CN type IMPORTANT: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Page 4
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Shield cable must be used. *iDP-562-RSL/RS, iDP-562-RSL2, iDP-562-CNL/CN type. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
1. Outline iDP-562 is a impact dot printer. The compact and light weight printer is sufficiently provided with various functions in order to suffice the requirements of personal computers. This printer is useful especially for receipts and data recording on normal and carboned roll papers.
17 Storage Temperature : -25 C~ 60 C (-13 F ~ 140 F) The interface specifications of the iDP-562-RSL and iDP-562-RSL2 are the same. The iDP-562-RSL uses an EPROM, and the iDP-562-RSL2 uses a masked ROM. CITIZEN 1.25 mm (W) 1 mm, External diameter 80 mm or less 231.5 mm (D)
Insert this plug in the plug socket under the prescribed voltage. 2 Power Switch As the power switch is turned on, initializing performance of the printer starts and the print head returns to the left end (home position). 3 Power Lamp The lamp lights up as power switch is on and turns off when the switch is off.
4.1 The Ribbon Cassette Installation For setting the ribbon, disconnect the power source beforehand. When the printing has been continued for many hours, be careful not touch printer head as it might be hot. Remove the printer cover. While inserting the ribbon into the space between the print head and the ribbon guide, press the cassette into the holder unit it clicks into place.
4. Insert the paper into insertion inlet on the rear side of the printer. 5. Turn on the power switch. And then press LF switch to forward the paper into the printer. 6. Fix the roll paper at paper holder and set the printer cover.
Any printing without paper and ink ribbon cassette may cause damage of printer head. 2. Replace the Cassette before ink ribbon is worn with rents. 3. Be careful not to drop any foreign matters, such as paper clips, pins and the like into your printer. Those can cause mechanical trouble.
MARK: Not ready for DATA receipt SPACE: Ready for DATA receipt Current loop When current between connector 17 pin and 24 pin is MARK (Current): Ready for DATA receipt SPACE (Non-current): Not ready for DATA receipt CITIZEN iDP-562 User’s Manual...
*OFF LF code is valid LF code is valid GERMANY FRANCE *OFF *OFF EVEN *OFF *OFF 9600 4800 1200 *OFF *OFF iDP-562 User’s Manual DSW-3 CR code is void LF code is void No Check *OFF 7 bit DATA 8 bit DATA 2400 1200...
Printer side Equivalent to 232 Output (DTR FAULT) Equivalent to 232 CITIZEN Direction Function RS232C CURRENT of Signal Frame GND Input DATA BUSY signal ALARM signal Input DATA BUSY signal Computer side iDP-562 User’s Manual LOOP A: Computer B: Printer...
Note: Resistance should be set so that Current Loop is restricted within 10 ~ 20 mA. (b) TTL Input (RD) Printer side Equivalent to 7407 Output (DTR FAULT) Note: Output is open collector. CITIZEN Computer side Computer side iDP-562 User’s Manual...
User’s Manual 5.5.2. Setting of Preset jumper Following function are available by setting preset jumper 1 ~ 6. Please turn off power and remove a bottom case before setting. iDP-562-RSL2 iDP-562-RSL/RS CITIZEN...
Page 18
(RS-232C / TTL level) DATA can be transferred at DTR = SPACE (CURRENT LOOP) At shipping all of preset jumper are set as A. CITIZEN Mode × × × : Both A and B can be set. iDP-562 User’s Manual...
STOP BIT is 1 or 2 BIT and its signal level is MARK. If SPACE LEVEL is read at STOP BIT, FRAMING ERROR occurs. CITIZEN 1. Start BIT 2. DATA BIT (+ Parity BIT) 3. Stop BIT (1 ~ 2 BIT) iDP-562 User’s Manual...
Other Errors When any trouble is found out at the printer, ALM LAMP informs the user this error. In this case, FAULT signal is SPACE, DTR signal is BUSY and the machine becomes deselect condition.
Page 21
3. The computer transfers 3rd BYTE of DATA after checking READY condition. The printer expects Double Buffer transfer at the first stage. Therefore, after completion of 1st BYTE of DATA reception, the printer waits for 2nd BYTE of DATA. The printer recognizes Single Buffer transfer for the absence of START BIT after 1 ~ 2 STOP BIT.
SELECT state. BUSY ...This is an output signal from the printer. When the printer is BUSY state, the signal is HIGH. FAULT ...This is an output signal from the printer indicating printer FAULT state. The signal is LOW during a ALARM state.
*OFF LF code is void LF code is valid GERMANY FRANCE *OFF *OFF Not for use iDP-562 User’s Manual DSW-3 *OFF CR code is valid CR code is void *OFF LF code is valid LF code is void...
Control Signal : ACK, BUSY, SLCT, STB, FAULT Connectors : Printer side – 57-40360 (AMPHENOL) or equivalent Cable side – 57-30360 (AMPHENOL) or equivalent CITIZEN PIN NO. Signal Name TWISTED PAIR GND TWISTED PAIR GND ______ FAULT iDP-562 User’s Manual...
“LOW” level 0.4 V MAX (c) Input / Output Conditions All the input signals are pulled up by 1 K ohms. (Fig. 7) All the output signals are pulled up by 3.3 K ohms. (Fig. 8) CITIZEN (Fig.7) (Fig. 8) iDP-562 User’s Manual...
100 ns MAX 7 TYP 1100 ms MAX MAX When data is stored in input buffer. ______ (2) FAULT and SEL switch 500 ms TYP 10 ms MIN 550 ms TYP Note: preset by SEL is done manually. CITIZEN iDP-562 User’s Manual...
ESC + "0" 1B, 4F *ESC + "1" 1B, 31 *ESC + "2" 1B, 32 * Only for iDP-562-RS and iDP-562CN type. CITIZEN Designation of SI side character Designation of SO side character Function Feeds a new line after printing.
7.3 Input Data Format The input data to the printer is made by the codes listed in the Character Code Table. 1 Standard Character print Mode Designation US(1F) DATA Designation of standard character print mode is made immediately after power-on and initialization or after print.
Page 29
User’s Manual 4 Graphic Print Mode Designation ESC(1B) K(4B) DATA Input ESC K (1B 4B) at the top of the line and then input Graphic Print Data, which is converted to binary, into . After that, input dummy data in n If it is also the Graphic Print in the next line, ESC K n should be input once again before the data.
Page 30
FF(0C) With this code, paper feed goes on. If there is data in the buffer when this code is input, the printer dose form feed after the printing. The top of form for the next page is made in accordance with the page length which was specified with ESC C n.
The first line is set at the present line. Designation of reverse and red printing is cleared. For 7 BIT DATA, character code of SI is applied. *1. Printer becomes DESELECT (OFF-LINE) condition. (Model iDP-562-PSL2 type only.) CITIZEN iDP-562 User’s Manual...
User’s Manual 10. Maintenance With respect to maintenance: The mechanical part of the printer must be free from dirt and dust. Remove the printer cover periodically to clean printer mechanism with soft brush to eliminate any dirt and dust. CITIZEN...
Page 36
Information Systems Division Head Office CBM Bldg., 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Tel: (+81-3) 5345-7540 Fax: (+81-3) 5345-7541 70903330 09-20000210-5300-0040-005.83 Printed in Japan...